The Fixturlaser Smart Machine Checker is designed to be used by machinery mechanics to give a clear and accurate automatic diagnosis of rotating equipment. Requires no vibration expertise or internet connection.
Pre-Alignment Steps are the shaft alignment medication that reduces frustration and saves time in the long run!
ACOEM Fixturlaser proudly presents the predictive maintenance solution you've been waiting for, the RT-300. This machine reliability tool helps with precision shaft alignment and all machine diagnostics.
The augmented mechanic’s solution – RT-300 – is a smart reliability tool that combines on-the-spot machine diagnostics with tools for pre-alignment and precision shaft alignment, minimizing the time from fault diagnostics to corrective actions.
Precision shaft alignment of wind turbine generators mounted on adjustable chocks is as straightforward as when aligning rotating machinery mounted on chocks down at ground level.
In the case of a recent NXA Training Class in a Vestas V82 we knew before going up-tower that one revolution of the adjustable chocks equals 1mm. Also, as there are 6 holes in the chocks, we calculated that the hole t
Vibration analysis is a useful way to monitor machine health. Many plants have implemented regular vibration analysis plans to ensure the condition of their machines is being checked at regular intervals and so, if an issue comes to light after spectral analysis, a solution can be pursued.
When analyzing vibration, it is important to be familiar with several terms. These are:
Frequency
Disp
When performing vibration analysis, it is observed that machines with VFD drives have a more frequent occurrence for changing motor bearings. If you’ve been diligent in the installation and maintenance of these machines, ensuring the alignment and balance are within specification and the bearings are properly lubricated, but still have frequent bearing failures, it may be your VFD drive.
I’ll
If you’ve worked with machine tools before, you’ve likely heard the terms coaxiality, runout, cylindricity, roundness, and total runout, but do you know what each means?
In this post we will lay out each of these terms so that you know what each means and so you are able to grasp the difference between them, which will hopefully be helpful on the job.
Let’s begin with roundness. This can als
For the field portion of a recent training class, the decision was made to check the alignment on a plastic extruder. At first glance, checking the alignment of the motor shaft to gearbox input shaft is pretty straightforward. However, the output side of the gearbox had two shafts, so maybe this is not so straightforward. And to complicate things a little more, there are three more chambers couple
We want to offer some helpful maintenance tips from our trainers in a single blog post. This blog is a collection of useful troubleshooting tips, maintenance reminders, and pieces of advice from people who have been in the maintenance industry for many years and have seen a thing or two and want to pass their knowledge on to you!
We have categorized the tips below so that you can focus on the
Fixturlaser LEVEL is used for levelling machines or machine parts during installation and gives accurate measurement results. The measuring sensor measures the angular deviations from the surface in two axes using a wide measurement range (± 50 mm/m), high accuracy and with a resolution down to 0.01 mm/m.
When performing the Ariel ER-82 Top Plane Compressor Frame Measurement, surrounding reciprocating compressors in operation may cause repeatability issues due to excessive vibration.
Establishing good habits with sensor placement will get you one step closer to determining the health of any machine.
Recently, we was called to consult with a customer to recommend a procedure and alignment tools for a very long-distance vertical pump alignment. First, we will describe the machine and then how we aligned it. This large raw sewage pump machine train begins at the driver level. In this plant, floor levels are described by relationship to sea level. At the top level (+35), the primary mover, a
In shaft alignment, machines that run hot often have In shaft alignment, machines that run hot often have thermal growth targets. Thermal targeting simply means that the shafts may be misaligned while at room temperature, but as they heat up to operating temperature, they will “grow” into alignment.
But where does the thermal growth target come from?
Many times, the machine manufact
ECOTECH Pty Ltd, ACOEM’s Australian subsidiary, is now helping to shape the longevity and sustainability of industrial and mining machinery across Australia and the Asia-Pacific region. The integration of Statewide Bearings’ (SWB Plus) Condition Monitoring & Fixturlaser Laser Alignment team into ECOTECH represents another step forward in ACOEM’s mission
Over the years we have fielded several technical support calls from maintenance personnel having repeatability and soft foot issues (during an alignment) all of which had a common issue; other influences. Meaning not the typical looseness, coupling backlash, soft foot issues.
During the “heat of the battle” to get the precision shaft alignment job finished it is easy to overlook simple items th
The Fixturlaser Smart Machine Checker is designed to be used by machinery mechanics to give a clear and accurate automatic diagnosis of rotating equipment. Requires no vibration expertise or internet connection.
This is as much a title for a blog as it is a question. One our Technical Trainers once stated that to align rotating machinery, they must first be alignable. What is meant in part by this is that when we have a collinear tolerance of 0.5mil /1” angularity and 2.0 mils offset, the machines must be mounted to a stable foundation to be able to hold the tolerance.
Flexion of the base in some cases
Proper use of any tool is essential to success in achieving your desired goal. Many tools have optional configurations to adapt that tool to your needs. Fixturlaser Precision Alignment Systems are no different. The alignment tools produced by Acoem/Fixturlaser are second to none in ease of use. The Acoem AB design engineers do all they can to provide the end user with an alignment tool that can be
